Advanced-technology FusionSwirl Manuel d'utilisateur télécharger pdf

ATI‐FSII Revision0 EffectiveDate:10/26/2011

AdvancedTechnology,Inc 800‐849‐1320 www.advtechnology.com

Page1of3



Installation Instructions for

FusionSwirl

™

is a decorated aluminum sheet that can be installed easily to various substrates, including

drywall.

STORAGE

Sheets should be stored indoors on a solid, flat, dry surface. Do not stack on concrete floor or

any other surface that emits moisture. Lay sheets flat with proper support on the ends of sheets.

Do not stand sheets on edge. Sheets should be stored in a cool, well-ventilated, dry area. Prior

to installation, allow sheets to acclimate to the room temperature and humidity for 24-48 hours in

the installation location.

MAINTENANCE

Clean surfaces with a soft cloth using a household cleaner – waxes, Windex type solutions, or

ordinary soap and water. Good furniture or automobile waxes can provide additional protection.

ALUMINUM SHEET LAMINATION

If adhering the sheet to a substrate first (good quality hardwood plywood, high density

particleboard, or MDF should be used as the substrate) - clean the substrate with a clean brush.

Inspect the sheet for quality prior to fabrication.

Laminate to substrate using techniques similar to working with HPL’s. Cut the sheet to size with

shears or a saw, and be sure that the blades are sharp. Leave the protective masking on the

product during machining/installation. Cut into the sheet so that rough edges are on the back of

the sheet. Sand down cut edges with 220 grit sandpaper. Files may also be used to de-bur

sharp edges, and always file down on the decorative surface. It is always best to test cut first to

confirm results.

ROUTING INFORMATION

Sharp multi-fluted carbide cutters are necessary; the larger the diameter the cutter the better the

results. It is important that the cutter travel direction is against the cutter rotation. ALWAYS CUT

DECORATIVE SIDE UP (into the decorative face). When routing, the less material removed, the

better. It is also important that the face of the material be protected from the base plate of the

router. For edge trimming, high speed trimmers should be used (approximately 22,000 RPM)

and will produce smooth burr-free edges. If using a CNC router refer to your CNC manual for

optimal settings for cutting aluminum.

SAWING INFORMATION

Table and/or panel saw: always use sharp carbide tipped blades with 80 to 100 teeth. Blade

should be 8” to 12” in diameter, and at 0 degree rake for best results. It is always best to cut into

the decorative face with the blade to minimize burring and edge distortion. Do not force material

through saw. A constant feed rate will produce smoother cuts. Blade wax will promote better

cuts.

1 2 3

CONDITIONS & WARRANTY 3
CAUTION 3

Résumé du contenu

Page 1

ATI‐FSII Revision0 EffectiveDate:10/26/2011AdvancedTechnology,Inc 800‐849‐1320 www.advtechnology.comPage1of3Installation Instructions

Page 2

ATI‐FSII Revision0 EffectiveDate:10/26/2011AdvancedTechnology,Inc 800‐849‐1320 www.advtechnology.comPage2of3SHEARS Blades must be clea

Page 3 - CAUTION

ATI‐FSII Revision0 EffectiveDate:10/26/2011AdvancedTechnology,Inc 800‐849‐1320 www.advtechnology.comPage3of3CONDITIONS & WARRANTY

Commentaires sur ces manuels

Pas de commentaire

Advanced-technology FusionSwirl Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Pour la maison Advanced-technology FusionSwirl. Advanced Technology FusionSwirl User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Pour la maison Advanced-technology FusionSwirl